dimensions in inches and (millimeters) db dbs .404(10.3) .386(9.80) .255(6.5) .245(6.2) .013(0.33) .0088(0.22) .013(0.33) .003(0.076) .060(1.53) .040(1.02) .205(5.2) .195(5.0) .047(1.20) .040(1.02) .335(8.51) .320(8.13) 0 45 .130(3.30) .120(3.05) features ideal for printed circuit board reliable low cost construction utilizing molded plastic technique high temperature soldering guaranteed: 260 o c / 10 seconds / 0.375? ( 9.5mm ) lead length at 5 lbs., ( 2.3 kg ) tension small size, simple installation high surge current capability maximum ratings and electrical characteristics rating at 25 o c ambient temperature unless otherwise specified. single phase, half wave, 60 hz, resistive or inductive load. for capacitive load, derate current by 20% db db db db db db db type number symbol units maximum recurrent peak reverse voltage v rrm 50 100 200 400 600 800 1000 v maximum rms voltage v rms 35 70 140 280 420 560 700 v maximum dc blocking voltage v dc 50 100 200 400 600 800 1000 v maximum average forward rectified current @t a = 40 o c i (av) 1.0 a peak forward surge current, 8.3 ms single half sine-wave superimposed on rated load (jedec method ) i fsm 50 a maximum instantaneous forward voltage @ 1.0a v f 1.1 v maximum dc reverse current @ t a =25 o c at rated dc blocking voltage @ t a =125 o c i r 10 500 ua ua typical thermal resistance ( note 1 ) r ja r jl 40 15 o c/w operating temperature range t j -55 to +150 o c storage temperature range t stg -55 to +150 o c notes: 1. thermal resistance from junction to amb ient and from junction to lead mounted on p.c.b. with 0.2? x 0.2? (5mm x 5mm) copper pads. 2. dbs for surface mount package. db101(s) - DB107(s) single phase 1.0 amp. glass passivated bridge rectifiers db db db db db db db 101s 102s 104s 103s 105s 106s 107s 107 106 105 104 103 102 101 http://www.luguang.cn mail:lge@luguang.cn
ratings and characteristic curves fig.2- typical reverse characteristics per bridge element 0 20 40 60 80 100 120 140 100 0.01 0.1 1 10 percent of rated peak reverse voltage. (%) tj=125 c 0 tj=25 c 0 fig.5- typical for w ard characteristics per bridge element inst ant aneous for w ard current . (a) 0.4 0.6 0.8 1.0 1.2 1.4 1.6 0.01 0.1 1 10 for w ard vol t age. (v) fig.4- typical junction cap acit ance per bridge element cap acit ance.(pf) 1 10 100 1 10 100 reverse vol t age. (v) tj=25 c f=1.0mhz vsig=50mvp-p 0 fig.1- maximum dera ting cur ve for output rectified current a verage for w ard current . (a) 20 40 60 80 100 120 140 150 0 0.5 1.0 ambient tempera ture. ( c) o 60hz resistive or inductive load inst ant aneous reverse current .( a ) tj=25 c pulse width-300 s 2% duty cycle 0 fig.3- maximum non-repetitive peak for w ard surge current peak for w ard surge current . (a) 1 2 4 6 10 20 100 60 40 0 10 40 60 50 20 30 number of cycles a t 60hz single sine - w ave (jedec method) copper pauls .51" x .51" (13mm x 13mm) .06" (1.5mm) pcb db101 ( s ) - DB107 ( s ) single phase 1.0 amp. glass passivated bridge rectifiers http://www.luguang.cn mail:lge@luguang.cn
|